Introduction
The Cisco Wireless Services Module 2 (WiSM2) Controller for Catalyst 6500 Series Switches is a highly scalable and flexible platform that enables systemwide services for mission-critical wireless in medium to large-sized enterprises and campus environments. Designed for 802.11n performance and maximum scalability, the WiSM2 controller supports a higher density of clients and delivers more efficient roaming, with at least nine times the throughput of existing 802.11a/g networks. The WiSM2 controller offers enhanced uptime with the ability to simultaneously manage up to 500 access points (APs); superior performance for reliable streaming video and toll quality voice; and improved fault recovery for a consistent mobility experience in the most demanding environments.Cisco Catalyst 6500 Series WiSM2 Controller
As a component of the Cisco Unified Wireless Network, this controller provides realtime communication betweenCisco Aironet access points, the Cisco Wireless Control System (WCS), and the Cisco Mobility Services Engine to deliver centralized security policies, wireless intrusion prevention system (IPS) capabilities, award-winning RF management, and quality of service (QoS). With CleanAir technology the WiSM2 protects 802.11n performance by providing cross-network access to real-time and historic RF interference information for quick, troubleshooting and resolution. This integrated approach to large-scale wireless networking, customers can realize significant total cost of ownership (TCO) benefits by streamlining support costs and reducing planned and unplanned network downtime.Features
Other features and characteristics of the WiSM2 controller are summarized here.
Note: Sup 720 software version 12.2.(33)SXJ is the minimum software required for operation with the WiSM2 controller.
Feature Parity with 5500 Appliance Controllers:
- Interoperability with other service modules and WiSM1
- Supports up to 500 APs/10,000 clients and 5,000 tags
- License upgrade from 100 APs in increments up to 500 APs
- Data Plane (Encrypted/Unencrypted/ACL) throughput of 10 Gbps
- Supports Sup720, Sup720-10G, Sup-2T, and 6500-E-Series chassis
- Supports Non-E Series with high speed fans
- Sup 720 Software Version 12.2(33)SXJ or higher
- Supports up to 7 blades in a chassis; 14 in VSS mode
- Supports up to 5 blades in a chassis when other service modules are present; 10 in VSS
- Support for OEAP
Prerequisites
Requirements
This is a list of components that are required when deploying WiSM2 in the Catalyst chassis:| Device/Application | SW Versions |
|---|---|
| Catalyst 650X with 720 Sup* | 12.2(33)SXJ or Higher |
| Ethernet Line-Cards - Tested and Compatible with WiSM2 | 6148, 6516, 6548, 6704-10Gb, 6708-10Gb, 6716-10Gb, 6748 and 6724 |
| WiSM2 Controllers | 7.0 MR1 ver 7.0.116.0 |
| WCS | 7.0 MR1 ver 7.0.172.0 |
* The Catalyst chassis on which the Cisco WiSM2 is installed needs a Supervisor 720 module.
The information in this document was created from the devices in a specific lab environment. All of the devices used in this document started with a cleared (default) configuration. If your network is live, make sure that you understand the potential impact of any command.
Related Products
WiSM2 operates with the Supervisor 720 family, including:- FS3 Supervisor 720 (WS-SUP720) – Also referred to as the Supervisor 720-3a.
- FS4 Supervisor 720-3B (WS-SUP720-3B) – This is an update of the original Supervisor 720 adding support for a number of new hardware-based features like MPLS and ACL counters.
- FS5 Supervisor 720-3BXL (WS-SUP720-3BXL) – Provides the same hardware feature capabilities as a Supervisor 720-3B, but also adds increased capacity for storing up to 1 Million IPV4 routes.
- FS6 Supervisor 720-3C-10GE and Supervisor 720-3CXL-10GE – Adds support for 2 x 10GE uplink ports on the front panel as well as support for a number of new hardware features like support for Virtual Switch Link (VSL).
Note: WiSM2(s) are supported in the –E Series chassis.
* Supervisor slots not recommended as WiSM2 slots.
Note: WiSM2(s) are supported in the above Non-E-Series chassis with HS fan trays.
Conventions
Refer to Cisco Technical Tips Conventions for more information on document conventions.Basic WiSM2 and Catalyst 6500 Topology
Initial System Configuration
Complete these steps:- Upgrade the Catalyst 65XX with the IOS software 12.2(33)SXJ provided on Cisco.com. Only after upgrading the Catalyst IOS software will the system recognize the WiSM2 blade. Upgrade of the Catalyst IOS can be done via TFTPing the new IOS software to the system or by simply copying the image into the flash card. The flash card has to be 256 MB in size or larger. Here is an example:
CAT6504-MA#dir disk1: Directory of disk1:/ 1 -rw- 4713 Jul 12 2010 20:36:44 +00:00 cat6504-ma 2 -rw- 8112 Mar 1 2007 19:18:56 +00:00 running-config 3 -rw- 130796804 Mar 30 2011 14:49:24 +00:00 s72033-adventerprise_wan-mz.122-33.SXJ.bin 512040960 bytes total (381222912 bytes free) - Issue the reload command on the Cat650X in order to restart the Cat65XX. Then, reboot the system with the new image and make sure the "boot image" is pointing to the new Catalyst IOS image on the system or the flash disk as in this example:
rommon 1 > dir disk1: Initializing ATA monitor library... Directory of disk1: 5 130796804 -rw- s72033-adventerprise_wan-mz.122-33.SXJ.bin 35816 4713 -rw- cat6504-ma 4 8112 -rw- running-config rommon 2 > boot disk1:s72033-adventerprise_wan-mz.122-33.SXJ.bin
- After you reload with the new software, the sh version command will show the version of software as posted on Cisco.com. Make sure the proper software is loaded:
CAT6504-MA#sh version Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISE_WAN-M), Version 12.2(33)SXJ, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2011 by Cisco Systems, Inc. Compiled Thu 17-Mar-11 15:10 by prod_rel_team ROM: System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
- Insert the WiSM2 board in the available 65XX- E slot and issue the sh module command on the Cat65XX. The WiSM2 module has to appear in the list:
CAT6504-MA#sh module Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 1 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL SAL1101CWTQ 2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL09497FS3 3 4 WiSM 2 WLAN Service Module WS-SVC-WISM2-K9 SAL1421JDER Mod MAC addresses Hw Fw Sw Status --- ---------------------------------- ------ ------------ ------------ ------- 1 0017.9568.72b4 to 0017.9568.72b7 5.3 8.4(2) 12.2(33)SXJ Ok 2 0016.470d.ec04 to 0016.470d.ec33 10.2 7.2(1) 12.2(33)SXJ Ok 3 0011.92ff.ed20 to 0011.92ff.ed2f 0.5 12.2(18r)S1 12.2(33)SXJ Ok Mod Sub-Module Model Serial Hw Status ---- --------------------------- ------------------ ----------- ------- ------- 1 Policy Feature Card 3 WS-F6K-PFC3BXL SAL1052CK95 1.8 Ok 1 MSFC3 Daughterboard WS-SUP720 SAL1052CK3E 2.6 Ok 2 IEEE Voice Daughter Card WS-F6K-GE48-AF SAL094978HV 1.2 Ok Mod Online Diag Status ---- ------------------- 1 Pass 2 Pass 3 Pass CAT6504-MA#
- If the module is not on the list, reset the system again. If the module is shown in the list, proceed with the next step.
Note: The next few steps are done to install/upgrade and configure the software on the WiSM2 in the Catalyst 65XX switch. - You can load the software via the command line interface. Configuration via WebUI is not available at this point since the Management Interface on the wireless controller is not configured yet. The controller should be configured to operate properly on your network and configured with the IP addresses of your working subnets. You can configure the wireless controller by directly attaching it to the console ports on the WiSM2 controller or opening a console session to the controller module from the Catalyst interface as shown here.
Note: You can access the WiSM2 through a session command directly now.
CAT6504-MA#session slot 3 processor 1 The default excape character is Ctrl-^, then x. You can also type 'exit' at the remote prompt to end the session Trying 192.168.2.21 ... Open (WiSM-slot3-1) User: admin Password:******* (WiSM-slot3-1) >
- After configuring the WiSM2 controller and issuing the show sysinfo command, you should see this output with Mgmt interface IP address of 10.70.0.10:
(WiSM-slot3-1) >show sysinfo Manufacturer's Name.............................. Cisco Systems Inc. Product Name..................................... Cisco Controller Product Version.................................. 7.0.114.114 Bootloader Version............................... 1.0.7 Field Recovery Image Version..................... 1.0.0 Firmware Version................................. FPGA 1.6, Env 0.0, USB console 2.2 Build Type....................................... DATA + WPS System Name...................................... Jian1-ma System Location.................................. TME Lab - Mike's Rack System Contact................................... Mike Adler System ObjectID.................................. 1.3.6.1.4.1.9.1.1293 IP Address....................................... 10.70.0.10 Last Reset....................................... Watchdog reset System Up Time................................... 0 days 0 hrs 11 mins 46 secs System Timezone Location......................... Current Boot License Level....................... base Current Boot License Type........................ Evaluation Next Boot License Level.......................... base Next Boot License Type........................... Evaluation Configured Country............................... US - United States --More-- or (q)uit State of 802.11b Network......................... Enabled State of 802.11a Network......................... Enabled Number of WLANs.................................. 3 Number of Active Clients......................... 0 Burned-in MAC Address............................ 00:11:92:FF:EC:00 Maximum number of APs supported.................. 100 (WiSM-slot3-1) >
- If you need to reset the WiSM2 controller in the Catalyst chassis, use this command:
If you need to reset the controller to factory defaults - watch the screen, while attached to the console port on the WiSM2 controller, for the reset option to come up and then hit <esc> key. In the controller menu, choose option 4 to reset the controller to factory defaults. In order to power the WiSM2 wireless controller in the Catalyst chassis OFF or ON, use this command:(Config)# hw module <#> reset
(Config)#power enable module <#>
Configure Sup720 and WiSM2 Communication
Complete these steps in order to configure Sup 720 – WiSM2 communication:- The Catalyst 65XX-E SUP module will communicate to the WiSM2 board via internal Service port interface on the WiSM2 card. Complete these steps in order to properly configure the interfaces and VLANs on the Catalyst 65XX to communicate properly with the WiSM2 blade. The Service port on the WiSM2 card should be configured for DHCP address or static IP address.
Note: Service Port IP address should be on the different subnet from the Management interfaces of the controller. - Create a VLAN in the Supervisor 720. This VLAN is local to the chassis and is used for communication between Cisco WiSM and Catalyst Supervisor 720 over a Gigabit interface on the Supervisor and service-port in the Cisco WiSM.
Note: All VLAN numbers and IP addresses are examples.
!--- Assign an appropriate IP address and !--- subnet mask for VLAN 22 interface Vlan22 ip address 192.168.2.1 255.255.254.0 - If during controller configuration you chose the DHCP address for the service port, create a DHCP scope for the service port of the Cisco WiSM in Supervisor 720 or on a standalone DHCP server:
Ip dhcp excluded-address 192.168.2.1 192.168.2.50
- Associate the VLAN for the service port.
!---Configure this command to use vlan 22 !--- in order to communicate with the service-port. wism service-vlan 22 - Issue the show wism status command in order to verify that the Cisco WiSM received an IP address from the DHCP server.
Cat650X# show wism status
Manual LAG configuration is not supported in Cisco IOS Software Releases 12.2(33) SXI and later. Auto-lag will be created by the system automatically for you.CAT6504-MA#sh wism status Service Vlan : 22, Service IP Subnet : 192.168.2.1/255.255.254.0 WLAN Management Slot Controller Service IP IP SW Version Controller Type Status ----+-----------+-------------+-----------+-----------+-----------------+------- 3 1 192.168.2.21 10.70.0.10 7.0.114.114 WS-SVC-WISM-2-K9 Oper-Up CAT6504-MA#
!--- Create the VLAN in the Supervisor 720 !--- in order to communicate with the management port !--- Assign an appropriate IP address and subnet !--- mask for VLAN 70 ! interface Vlan70 description Management VLAN for WiSM-2 ip address 10.70.0.5 255.255.255.0 end !
- The Supervisor automatically creates a port-channel interface for the independent controller in the Cisco WiSM2 as soon as the module is detected. Usually, the port-channels have a high number, such as 405 in this example:
Cat650X#sh ip int brief
GigabitEthernet3/4 unassigned YES unset administratively down down Port-channel3 unassigned YES unset down down Port-channel405 unassigned YES unset up up Vlan1 unassigned YES NVRAM administratively down down Vlan22 192.168.2.1 YES NVRAM up up VLAN70 10.70.0.5 YES NVRAM up up Vlan192 192.168.0.1 YES NVRAM up up CAT6504-MA#
- Additionally, make sure that you allow VLANs that are configured in the Cisco WiSM2 through the port-channel and Gigabit interfaces with these commands. Make sure the VLANs are also active.
Note: Configure the controller with this commands. Here is an example:Cat-6K(config)# wism module {#} controller {#} allowed-vlan {vlan range} Cat-6K(config)# wism module {#} controller {#} native-vlan {vlan id} Cat-6K(config)# wism module {#} controller {#} qos {trust/vlan-based} <dscp/cos/ip-precedence> - Trust state of theLAG Interface
Note: See Appendix B for a complete example of the Catalyst 6504 configuration.! wism module 3 controller 1 allowed-vlan 10-120 wism module 3 controller 1 native-vlan 70 wism module 3 controller 1 qos vlan-based !
- The new command Cat-6K(config)#wism module {#} controller {#} qos vlan-based- VLAN Based QoS should be enabled for policing the wireless to wired traffic on the Catalyst 6K.
- Verify the previous configuration command execution:
#show wism module 3 controller 1 status
CAT6504-#show wism module 3 controller 1 status WiSM Controller 1 in Slot 3 configured with auto-lag Operational Status of the Controller : Oper-Up Service VLAN : 22 Service Port : 3 Service Port Mac Address : 0011.92ff.ec01 Service IP Address : 192.168.2.21 Management IP Address : 10.70.0.10 Software Version : 7.0.114.114 Port Channel Number : 405 Allowed-vlan list : 10-100 Native VLAN ID : 70 WCP Keep Alive Missed : 0 CAT6504-MA#
- Summary: The Cisco WiSM2 controller is inserted into the appropriate slot and powered on. The basic configuration is completed with the help of the setup script. With the completion of basic configuration, you can configure the Cisco WiSM2 controller through the console CLI or through the Cisco WiSM2 controller web-interface. In order to use the session command, you have to make sure that the service port on the Cisco WiSM2 is assigned a static or DHCP assigned IP address. You need to configure WLC separately in the Cisco WiSM2 module, initially from the CLI and then from the web interface.
- Now you can connect to the controller management interface via GUI or console session with your laptop connected with Ethernet or wireless connection and continue the configuration.
- Check the Licenses available on the controller. If the count is zero, contact License TAC support team to refresh the Licenses.
- Have the APs join the WiSM2 across a Layer 2/3 network switch.
- Have the Wireless Clients connect to the LAP and send traffic to the external servers and other wireless clients and make sure traffic (that is, ping) makes it through without any drops.
- This completes Basic Sup 720 and WiSM2 configuration. Additional configuration changes can be made via the WebUI interface just like on any other wireless controller. This WiSM2 deployment guide does not go into details of the wireless controller configuration.
Configure WiSM2 from WCS
Just like any other wireless controller, the WiSM2 controller can be configured from the WCS. WCS ver 7.0.172.0 or higher is required for WCS to recognize and configure WiSM2 controllers.
The image below shows how a WCS manages WiSM and WiSM2 controllers, including the slots in which they are inserted and the internal port to which they are connected.
Note: WiSM always comes up as two controllers and the new WiSM2 shows as one controller.
Configure Sup720 and WiSM2 Communication in a VSS Mode
The key enabler of the VSS technology is a special link that binds the two chassis together, called a Virtual Switch Link (VSL).
Note: Supervisor 720-3C-10GE or Supervisor 720-3CXL-10GE required to support VSS mode.
The most important change with the Cisco WiSM in a VSS environment is the way you access and manage it. In a Cisco VSS environment, a switch ID is required for many commands used to administer the WiSM2.
The slots start from 17 and ends in 29 for 13 slot chassis for Switch 1, and from 33 and ends in 45 for 13 slot chassis switch 2.
Cat650X# show module switch {#} slot {#}
Cat650X#show wism status - Shows the WiSM2 modules in VSS switch.show module switch 2 slot 11
VSS#show wism status
Service vlan : 8, Service IP Subnet : 8.100.1.8/255.255.255.0
WLAN
Slot Controller Service IP Management IP SW Version Controller Type Status
----+----------+-----------+--------------+------------+----------------+-------
18 1 8.100.1.59 10.173.1.10 7.0.114.62 WS-SVCWISM-2-K9 Oper-Up
25 1 8.100.1.90 10.178.1.10 7.0.114.62 WS-SVCWISM-2-K9 Oper-Up
34 1 8.100.1.65 10.172.1.10 7.0.114.62 WS-SVCWISM-2-K9 Oper-Up
36 1 8.100.1.63 10.170.1.10 7.0.114.62 WS-SVCWISM-2-K9 Oper-Up
Manual LAG configuration is not supported in Cisco IOS Software Releases 12.2(33)SXJ and later. Auto-lag configuration will be configured for you by the system.The Supervisor Module automatically creates two port-channel interfaces for the two independent controllers in the VSS switch for WiSM2s as soon as the module is detected. Usually the port-channels have a high number. The EtherChannel for WiSM2 starts from 689 and ends in 746.
The Catalyst 65XX-E VS-S720-10G module will communicate to the WiSM2 boards via internal Service VLAN that has to be defined just like a single chassis configuration:VSS#show wism switch 2 module 4 controller 1 status WiSM Controller 1 in slot 36 configured with auto-lag Operational Status of the Controller : Oper-up Service VLAN : 8 Service Port : 3 Service Port Mac Address : 0022.bdd5.0141 Service IP Address : 10.100.1.63 Management IP Address : 10.170.1.10 Software Version : 7.0.114.62 Port Channel Number : 727 Allowed-vlan list : 100-120,122-140,142-260,262-340,348-450, 459,471-480,499 Native VLAN ID : 420 WCP Keep Alive Missed : 0 VSS#
(Cat-6K)# wism service-vlan {vlan id}
Example of configuration on the Catalyst 6500:Create a DHCP scope for the Service Port of the Cisco WiSM2 in Supervisor 720 or on a standalone DHCP server. For Example:interface vlan22 ip address 192.168.2.1 255.255.254.0 wism service-vlan 22
Allow VLANs that are configured in the Cisco WiSM2 through the port-channel and Gigabit interfaces with these commands:Ip dhcp excluded-address 192.168.2.1 192.168.2.50
Cat-6K(config)# wism switch (#) module {#} controller 1 allowed-vlan {vlan range}
Cat-6K(config)# wism switch (#) module {#} controller 1 native-vlan {vlan id}
Cat-6K(config)# wism switch (#) module {#} controller 1 qos trust <dscp/cos/ip-precedence> - Trust state of the Interface
Cat-6K(config)# wism switch (#) module {#} controller 1 qos vlan-based- VLAN Based QoS should be enabled for policing the wireless to wired traffic on Catalyst 6K.
To verify the proper module installations in the VSS mode, issue this command:
show wism switch 2 module 4 controller 1 status
VSS#show wism switch 2 module 4 controller 1 status WiSM Controller 1 in slot 36 configured with auto-lag Operational Status of the Controller : Oper-up Service VLAN : 8 Service Port : 3 Service Port Mac Address : 0022.bdd5.0141 Service IP Address : 10.100.1.63 Management IP Address : 10.170.1.10 Software Version : 7.0.114.62 Port Channel Number : 727 Allowed-vlan list : 100-120,122-140,142-260,262-340,348-450, 459,471-480,499 Native VLAN ID : 420 WCP Keep Alive Missed : 0
show interface status switch 2 module 4
Cat6500#Show module switch – In oprder to verify the modules in the 2 VSS switches.VSS#show interfaces status switch 2 module 4 Port Name Status Vlan Duplex Speed Type Te2/4/1 connected trunk full 10G 10GBase Svc Te2/4/2 notconnect unassigned full 10G 10GBase Svc Gi2/4/3 connected 8 full 1000 1000Base Svc Gi2/4/4 disabled 1 full 1000 1000Base Svc VSS# VSS#
You can now connect to the controller management interface via GUI or console session with your laptop connected with Ethernet or Wireless connection and continue configuration.VSS#show module switch Switch Number: 1 Role: Virtual Switch Active ---------------------- ----------------------------- Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 1 6 Firewall Module WS-SVC-FWM-1 SAD0948020X 2 4 WiSM 2 WLAN Service Module WS-SVC-WISM2-K9 SAL1421JDEF 3 6 Firewall Module WS-SVC-FWM-1 SAD1404027Z 5 8 Intrusion Detection System WS-SVC-IDSM-2 SAD100304T6 6 4 WiSM 2 WLAN Service Module WS-SVC-WISM2-K9 SAL14481073 7 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL13410X3Y 9 4 WiSM 2 WLAN Service Module WS-SVC-WISM2-K9 SAL1421JENZ 10 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAD114900Y3 11 16 CEF720 16 port 10GE WS-X6716-10GE SAD112908Z2 12 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL09444NPS Switch Number: 2 Role: Virtual Switch Standby ---------------------- ------------------------------ Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 2 4 WiSM 2 WLAN Service Module WS-SVC-WISM2-K9 SAL1421JDFJ 3 8 Intrusion Detection System WS-SVC-IDSM-2 SAD103103TH 4 4 WiSM 2 WLAN Service Module WS-SVC-WISM2-K9 SAL1412DAKJ 5 8 Intrusion Detection System WS-SVC-IDSM-2 SAD094902UX 6 6 Firewall Module WS-SVC-FWM-1 SAD10450180 8 5 Supervisor Engine 720 10GE (Hot) VS-S720-10G SAL1332VP1Q 11 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL09433SP8 13 16 CEF720 16 port 10GE WS-X6716-10GE SAD112504YY
Check the Licenses available on the controller. If the count is zero, contact License TAC support team to refresh the Licenses.
Have the APs join the WiSM2 across a Layer 2/3 network switch.
Have Wireless Clients connect to the LAP and send traffic to external servers and other wireless clients and make sure traffic (that is, ping) makes it through without any drops.
This completes Basic Sup 720 and WiSM2 configuration. Additional configuration changes can be made via the WebUI interface just like on any other wireless controller. This WiSM2 deployment guide does not go into the details of wireless controller configuration.
This also completes VSS installation of the WiSM2 modules in the Catalyst VSS configuration. Additional configuration changes can be made via the WebUI interface just like on any other wireless controller. This WiSM2 deployment guide does not go into the details of wireless controller configuration.
Appendix A: Basic Switch and WiSM2 Terminology
| Term | |
|---|---|
| AP | Access Point |
| APM | AP Manager Interface |
| DEC | Distributed EtherChannel |
| DFC | Distributed Forwarding Card |
| DynInt | Dynamic Interface |
| FWSM | Firewall Service Module |
| IDSM | Intrusion Detection Service Module |
| ISSU | In Service Software Upgrade |
| LAG | Link Aggregation |
| MEC | Multichassis EtherChannel |
| Mgmt | Management Interface |
| NAM | Network Analysis Module |
| OIR | Online Inserted and Removal |
| Port | Physical Gbps port |
| RSPAN | Remote SPAN |
| SPAN | Switch Port Analyzer |
| SSO | Stateful Switchover |
| STP | Spanning Tree Protocol |
| VACL | VLAN Access Control List |
| VLAN | Virtual LAN |
| VSL | Virtual Switch Link |
| VSS | Virtual Switch System |
| WCP | Wireless Control Protocol |
| WCS | Wireless Control System |
| WiSM | Wireless Services Module |
Appendix B: Catalyst 6504 Example of Running Config
CAT6504-MA#sh run Building configuration... Current configuration : 4804 bytes ! ! Last configuration change at 20:34:02 UTC Tue Apr 12 2011 ! version 12.2 service timestamps debug uptime service timestamps log uptime no service password-encryption service counters max age 10 ! hostname CAT6504-MA ! boot-start-marker boot system flash s72033-adventerprisek9_wan_dbg-mz.SIERRA_INTEG_100903 boot-end-marker ! no logging console ! no aaa new-model ! ip dhcp excluded-address 192.168.1.1 192.168.1.10 ip dhcp excluded-address 192.168.2.1 192.168.2.20 ip dhcp excluded-address 192.168.0.1 192.168.0.20 ! ip dhcp pool wism-service-port network 192.168.2.0 255.255.255.0 default-router 192.168.2.1 ! no mls acl tcam share-global mls netflow interface mls cef error action freeze ! spanning-tree mode pvst no spanning-tree optimize bpdu transmission spanning-tree extend system-id wism service-vlan 22 wism module 3 controller 1 allowed-vlan 10-100 wism module 3 controller 1 native-vlan 70 wism module 3 controller 1 qos vlan-based diagnostic bootup level minimal port-channel per-module load-balance ! redundancy main-cpu auto-sync running-config mode sso ! vlan internal allocation policy ascending vlan access-log ratelimit 2000 ! interface Port-channel3 switchport switchport trunk encapsulation dot1q switchport trunk native vlan 70 switchport mode trunk mls qos trust dscp ! interface GigabitEthernet1/1 --More-- switchport mode trunk mls qos trust dscp ! interface GigabitEthernet1/1 switchport switchport trunk encapsulation dot1q switchport trunk native vlan 10 switchport mode trunk ! interface GigabitEthernet1/2 no ip address ! Truncated ….. interface Vlan22 description communication VLAN btween Sup720 and WiSM-2 ip address 192.168.2.1 255.255.254.0 ! interface Vlan70 ip address 10.70.0.5 255.255.255.0 ! ip classless ip forward-protocol nd ! no ip http server ! control-plane ! dial-peer cor custom ! line con 0 line vty 0 4 login line vty 5 15 login ! end CAT6504-MA#
